Vehicles
100 not categorized PORSCHE 944S EMBLECan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.PT34915 Permatune has long been a favorite alternative to the outrageously priced Bosch electronic ignition control unit. Today’s perma-tune is all new on the inside, and bolts up and plugs in to the same location as the stock system. The units increase spark energy to three times that of the stock ignition system. This is why spark plugs will never foul again, even when set to large spark plug gaps and will actually recover from fuel contamination. This increase in spark energy allows your engine to make more power for the same amount of fuel. Meticulously assembled by fellow americans in texas, the permatune outperforms the Bosch unit and at a much lower price. Installation is a direct plug-in. Get the spark back i...(choose a part on the right to read more) General Fitment911 1974-77
$701.38
Make a selection FVD123020ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection FVD33104381 The tow link is the furthest rear control arm on the rear axle. It is responsible for the toe angle adjustment. The OEM control arm bushings are simply too soft for track events and the teflon monoball racing bushings are too far too hard and noisy for street cars. Our sport bushings are made of a denser rubber (85 shore opposed to OEM 65 shore), which means that they are suitable for street and track use. Equally as important is that they do not produce any noise like the teflon bushings. FVD sport control arm facts: - better handling and more responsive. - makes precision adjustments of the suspension easier. - does not produce noise. - shore a hardness value of 85 for durability and handling. - fit's like o...(choose a part on the right to read more)
$482.89
Make a selection POR1100 Techna fit's d.o.t. Certified, high performance, brake line kits are made to fit all makes and models of cars.our brake lines are made of the finest ptfe hose and permanently crimped-on zinc plated steel fittings. Our hose is made with an extruded ptfe core and a stainless steel wire braided cover. They reduce volumetric expansion giving you the reliability and safety you demand. Overtime and under continuous use, OEM rubber lines can swell and expand, exposing the driver to brake fade. The rubber cover is also vulnerable to attacks from the ozone layer rubber which causes it to deteriorate. In extreme applications (auto x, racing, hard driving) rubber hoses might be susceptible to flying debris. Stainless ste...(choose a part on the right to read more) General Fitment911 1989-94
$121.50
Make a selection FVD34101702RAT We will send you a reconditioned control arm, kindly send back your old part, or core . The reconditioned control arm has been full inspected, disassembled, degreased and we have properly installed FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. This part is sold on an exchange basis, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and r...(choose a part on the right to read more)
$440.00
Make a selection FVD34101707AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. The reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD341999r. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform you immediately. General Fitment911 1989-94
From $418.00
Make a selection FVD34101702ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD34101802RAT We will send you a reconditioned control arm, kindly send back your old part, or core . The reconditioned control arm has been full inspected, disassembled, degreased and we have properly installed FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner please note: each control arm is remanufactured in Germany, so the lead times can vary. This part is sold on an exchange basis, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and re...(choose a part on the right to read more)
$440.00
Make a selection GR0890100 Suitable for bonding rubber mouldings to polished, primed or painted metals, wood, various plastics, etc. General FitmentACCESSORY
$29.99
Make a selection FVD559213 Includes the later model (series iii from 2009) water cooled crest, gasket and emblem securing nuts. Size: 67 mm x 51 mm sold individually. 1 is necessary per car.
$226.72
Make a selection FVD559211 Includes the early model (series i) air cooled crest, gasket and emblem securing nuts. Size: 67 mm x 51 mm sold individually. 1 is necessary per car.
$225.23
Make a selection MISWEBTB201 Factory dual weber carb rebuild kit contains everything you need for a perfect rebuild including instructions. can't get your carburated 914 to idle? does it run on three cylinders and piss and pop? Has it been sitting for half a year? take those carbs apart and rebuild them! it's easy and simple. make sure you soak the disassembled bodies in carb cleaner overnight however! order a nice set of our permanent replacement air filter assemblies while you are at it. two required per car. General Fitment914 1970-76
$28.50
Make a selection POR1020 Techna fit's d.o.t. Certified, high performance, brake line kits are made to fit all makes and models of cars.our brake lines are made of the finest ptfe hose and permanently crimped-on zinc plated steel fittings. Our hose is made with an extruded ptfe core and a stainless steel wire braided cover. They reduce volumetric expansion giving you the reliability and safety you demand. Overtime and under continuous use, OEM rubber lines can swell and expand, exposing the driver to brake fade. The rubber cover is also vulnerable to attacks from the ozone layer rubber which causes it to deteriorate. In extreme applications (auto x, racing, hard driving) rubber hoses might be susceptible to flying debris. Stainless ste...(choose a part on the right to read more) General Fitment911 1989-94
$121.50
Make a selection FVD34101802RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$438.90
Make a selection POR1700 Techna fit's d.o.t. Certified, high performance, brake line kits are made to fit all makes and models of cars.our brake lines are made of the finest ptfe hose and permanently crimped-on zinc plated steel fittings. Our hose is made with an extruded ptfe core and a stainless steel wire braided cover. They reduce volumetric expansion giving you the reliability and safety you demand. Overtime and under continuous use, OEM rubber lines can swell and expand, exposing the driver to brake fade. The rubber cover is also vulnerable to attacks from the ozone layer rubber which causes it to deteriorate. In extreme applications (auto x, racing, hard driving) rubber hoses might be susceptible to flying debris. Stainless ste...(choose a part on the right to read more) General Fitment911 1998-05
$121.50
Make a selection POR2101 Techna fit's d.o.t. Certified, high performance, brake line kits are made to fit all makes and models of cars.our brake lines are made of the finest ptfe hose and permanently crimped-on zinc plated steel fittings. Our hose is made with an extruded ptfe core and a stainless steel wire braided cover. They reduce volumetric expansion giving you the reliability and safety you demand. Overtime and under continuous use, OEM rubber lines can swell and expand, exposing the driver to brake fade. The rubber cover is also vulnerable to attacks from the ozone layer rubber which causes it to deteriorate. In extreme applications (auto x, racing, hard driving) rubber hoses might be susceptible to flying debris. Stainless ste...(choose a part on the right to read more) General FitmentCAYENNE 2007-10
$121.50
Make a selection PT924W Permatune has long been a favorite alternative to the outrageously priced Bosch electronic ignition control unit. Meticulously assembled by fellow americans in texas, the permatune outperforms the Bosch unit and at a much lower price. Installation is a direct plug-in. Get the spark back in your life today! Output: 350 volts, 3 amps. General Fitment924 1976-79924 1980-85
$658.78
Make a selection POR900 Techna fit's d.o.t. Certified, high performance, brake line kits are made to fit all makes and models of cars.our brake lines are made of the finest ptfe hose and permanently crimped-on zinc plated steel fittings. Our hose is made with an extruded ptfe core and a stainless steel wire braided cover. They reduce volumetric expansion giving you the reliability and safety you demand. Overtime and under continuous use, OEM rubber lines can swell and expand, exposing the driver to brake fade. The rubber cover is also vulnerable to attacks from the ozone layer rubber which causes it to deteriorate. In extreme applications (auto x, racing, hard driving) rubber hoses might be susceptible to flying debris. Stainless ste...(choose a part on the right to read more) General Fitment911 1965-69
$121.50
Make a selection POR1200 Techna fit's d.o.t. Certified, high performance, brake line kits are made to fit all makes and models of cars.our brake lines are made of the finest ptfe hose and permanently crimped-on zinc plated steel fittings. Our hose is made with an extruded ptfe core and a stainless steel wire braided cover. They reduce volumetric expansion giving you the reliability and safety you demand. Overtime and under continuous use, OEM rubber lines can swell and expand, exposing the driver to brake fade. The rubber cover is also vulnerable to attacks from the ozone layer rubber which causes it to deteriorate. In extreme applications (auto x, racing, hard driving) rubber hoses might be susceptible to flying debris. Stainless ste...(choose a part on the right to read more) General Fitment928 1983-86
$121.50
Make a selection PT911SC Permatune has long been a favorite alternative to the outrageously priced Bosch electronic ignition control unit. Meticulously assembled by fellow americans in texas, the permatune outperforms the Bosch unit and at a much lower price. Installation is a direct plug-in. Output: 350 volts, 3 amps. this unit is a direct replacement for the original Bosch unit and has a great guarantee. General Fitment911 1978-83911 1984-86 911 1987-89
$720.00
Make a selection PT928 Permatune has long been a favorite alternative to the outrageously priced Bosch electronic ignition control unit. Meticulously assembled by fellow americans in texas, the permatune outperforms the Bosch unit and at a much lower price. Installation is a direct plug-in. Get the spark back in your life today! Output: 350 volts, 3 amps. General Fitment928 1978-82928 1983-86
$524.08
Make a selection PTTTL Permatune has long been a favorite alternative to the outrageously priced Bosch electronic ignition control unit. Meticulously assembled by fellow americans in texas, the permatune outperforms the Bosch unit and at a much lower price. Installation is a direct plug-in. Get the spark back in your life today! Output: 350 volts, 3 amps. General Fitment911 1989-94911 1994-98 968 1992-95
$447.22
Make a selection SNX012 We assembled this kit of four quality sonax European cleaning products for car show last-minute detailing and weekend cleaners that want to quickly and easily add that extra gloss to their car. The dashbaord cleaner is the perfect answer to clean and protect your vehicles interior: dashboards, instrument panels and door linings. Seals both flat and textured surfaces, making them feel satiny-smooty to the touch, never oily. Works electro-statically to repel dust and dirt. The upholstery & carpet cleaner gently and thoroughly removes stubborn dirt and stains from fabrics, upholstery, door panels, carpets and ceilings. The foaming action formula is rich in cleaning agents as well as neutralizing odors and leaving ...(choose a part on the right to read more) General FitmentACCESSORY
$54.72
Make a selection ST6301 Solitude, near stuttgart, Germany, has always been legendary for its track and its races. General Fitment356 1960-65356 1950-59
$1,425.00
Make a selection FVD123019ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |